Non-soap clay base grease, has homogeneous and smooth structure. It contains Molybdenum Disulphide in very low micron size and is in finely dispersed form. This grease is highly water resistant, can withstand high temperature up to 250°C and can take shock loads. It is not affected by mild acids and alkalies. Meets the requirements of IS: 12790-89 and IPSS: 1-09-008. Recommended for high temperature (120-250°C) applications in plain & roller bearings in heavy industries, automobiles, earthmoving equipments, bearings of trolleys working inside furnaces.
Grade
Worked Penetration
at 25ºC ± 0.5ºC
Resistance to water washout
% loss by mass max.
MoS2%
Hytem 250
280 - 310
8
3.0
ASIANOL MULTIPLEX GREASE
High quality lithium complex soap base grease, produced from high viscosity, high viscosity index base lub oil. It is fortified with anti rust, antiwear and antioxidant additives. It has extreme pressure properties and passes Timken OK load requirements of EP type greases. Meets requirements of IPSS: 1-09-020. Recommended for the centralised grease stations of steel plants in severe duty application areas like slabbing & billet mills, hot strip mills, cold rolling mills, blast furnaces where high temperature, water ingress and severe shock and load conditions are encountered.
Grade
Worked Penetration
at 25ºC ± 0.5ºC
Drop Point
ºC Min
Timken OK load
(Kg) Min
Multiplex 0
355 - 385
250
23
Multiplex 1
310 - 340
280
23
Multiplex 2
265 - 295*
290
23
Multiplex 3
220 - 260
290
23
* For centralised lubrication system of steel plants worked penetration at 25ºC (60 strokes) shall be 280 - 305.
ASIANOL GRAPHITED GREASE
Calcium base grease with graphite as filler made in low VI lub base oils. Meets the requirements of IS: 508-93. Recommended for use as lubricants for slow speed friction parts like open gears, chains, rams, geared pushers in ovens, elevators, ropes, where high load conditions exist.
Grade
Worked Penetration
at 25ºC ± 0.5ºC
Drop Point
ºC Min
Graphited Grease No. 1
310 - 340
95
Graphited Grease No. 2
265 - 295
100
Graphited Grease No. 3
175 - 205
95
ASIANOL LICAPLEX GREASE
High quality new generation lithium calcium complex greases, with extra superior water resistance clubbed with high operating temperature range and extreme pressure properties. Recommended for use in applications in heavy industries, in plain & roller bearings, gear boxes, gear couplings, centralised grease stations, earthmoving equipments, automobiles where water ingress/excess entry is there and these parts operate under high load and temperature.
Grade
Worked Penetration
at 25ºC + 0.5ºC
Drop Point
ºCMin
Timken OK
load(Kg)
Resistance to water washout % loss by mass max.
Licaplex 0
355 - 385
170
23
1
Licaplex 1
310 - 340
180
23
2
Licaplex 2
265 - 295 *
190
23
3
Licaplex 3
220 - 250
190
23
3
* For centralised lubrication system of steel plants worked penetration at 25ºC (60 strokes) shall be 280 - 305.
ASIANOL SUPRATECH WR GREASES
It is a specially formulated high temperature, tacky grease developed for application in Sponge iron rotary kilns end sealing. This grease is also suitable for medium loaded antifriction bearings working in hot zone, and where water washout is a problem. Supratech WR2 can be a lubrication problem solver in those areas where normal lithium base grease fails.
Grade
Worked Penetration
at 25ºC + 0.5ºC
Drop Point
ºCMin
Timken OK
Load (Kg) Min
Supratech WR2
270 - 300
280
25
ASIANOL SUPERPLEX WL 3-2 GREASE
This is a third generation, super quality grease specially formulated for very high load bearing, very high water / emulsion resistant, with high tackiness properties with heavy anti-wear and antirust properties. This grease is specially suitable for Hot Rolling / Cold Rolling Mill heavy duty higher diameter antifriction bearings of the work rolls. This grease will perform satisfactorily in extreme lubrication requirement conditions of bearings.
Grade
Worked Penetration
at 25ºC + 0.5º
Drop Point
ºCMin.
Timken OK
load Min Kg
SUPERPLEX WL 3-2
230 - 270
200
28
ASIANOL SUPEREXTEND PD GREASE
These greases are third generation, long life greases with high EP agent for lubrication of gears and bearings. The "00" and "0" consistency greases are most suitable for lubrication of gear boxes which are leaky, and where normal gear oil is not sufficient to check the wearout and pitting of gear teeth. The consistency "1" and "2" are suitable for application requiring `resistance to severe wearout' and longer life. Consistency "3" is suitable for electrical motor bearings where frequent refilling is to be avoided or is not practically possible.
Grade
Worked Penetration
at 25ºC + 0.5º
Drop Point
ºCMin.
Timken OK
load Min Kg
SUPEREXTEND PD 00
400 - 430
150
22
SUPEREXTEND PD 0
355 - 385
160
22
SUPEREXTEND PD 1
310 - 340
180
22
SUPEREXTEND PD 2
265 - 295
190
22
SUPEREXTEND PD 3
220 - 250
190
22
ASIANOL LITHREX SM GREASE
This is a specially developed Lithium base grease for application in steel plant sintering machine hydraulic sealing application where high temperature clubbed with tackiness properties are the main requirement to stop hot air leakage between pallets and the rubbing surface. This grease meets IPSS 1-09-005
Grade
WorkedPenetration
at 25ºC + 0.5º
Drop Point
ºCMin.
Timken OK
load Kg Min
LITHREX SM 2
280 - 305
180
22
ASIANOL SUPERPLEX OG GREASE
These greases are third generation, speciality greases with EP agent, tackifier, solid lubricants and a special additive for lubrication of open girth gears and support roller surface in bath lubrication system for Open Girth Gear-Pinion pair. These Greases keeps the wear out and pitting of gear teeth under control. This Grease can be cleaned easily unlike the bituminous compounds. These Greases sticks to the gear pinion roller surfaces and maintain a film of lubrication even under severe loads
;